Shopping Cart
Chevrolet Traverse Lambda 2009-2013 Interior Trim Kit, 22 pcs
3 Reviews
CHTX-09-22
€149.99
Tax included Manufacturing time 2-7 business days
Vehicle-specific decorative overlay kit for the existing interior surfaces of your Chevrolet Traverse. Choose the finish and verify the parts diagram before ordering.
| Make | Chevrolet |
|---|---|
| Model | Traverse |
| Model years | 2009-2013 |
| Generation | 1st generation (Lambda) |
| Generation built | 2009–2017 |
| Product type | 3D dashboard trim kit |
| Parts included | 22 |
| Product reference | CHTX-09-22 / Original Reference: 4241 |
| How to check your version | Before ordering, check on your vehicle and compare with the parts diagram: radio / NAVI unit, transmission, climate control. Steering wheel position (LHD/RHD): select it in the option below. |
CockpitDekor · vehicle-specific dashboard trim
Chevrolet Traverse Lambda dashboard trim kit, 22 pieces (2009–2013)
This kit covers the Chevrolet Traverse Lambda (2009–2013) with 22 pre-cut decorative pieces. They are applied over the existing trim, so the original panels stay in the car.
All kits for Chevrolet Traverse · Chevrolet dashboard trim kits
- VehicleChevrolet Traverse Lambda
- Years2009–2013
- Pieces22
- ReferenceCHTX-09-22
- FinishHigh-gloss as shipped · matte with 1 coat of clear matt spray before fitting
Material: depth you can see
Each piece is about 2–3 mm thick: a decorative layer under a clear, glossy coat of Italian ColorDec polyurethane with softly rounded edges, and a 3M adhesive layer on the back.
Wood and carbon looks are decorative surfaces – not real wood veneer and not structural carbon fibre.
Choose the finish
Wood grains, carbon weaves, brushed aluminium, piano black or a plain colour: every finish available for this kit is shown as a swatch in the selector above, so you see the surface before you order.
Each kit is made to order in the finish you select.
Check the fit before ordering
- Compare the parts diagram with your own dashboard: radio / navigation unit, gearbox (manual or automatic) and climate controls must match this version.
- Steering wheel side (LHD/RHD): choose it in the option below.
- Only the parts drawn on the diagram are included; mood photos do not define the contents.
Fitting and care
Clean and degrease the surface, dry-fit every piece first, then peel and press firmly. No tools are included; a detailing or wrap specialist can fit complex shapes for you.
Clean with a soft, slightly damp cloth – no abrasives or strong solvents.
Not a sticker, a domed 3D trim part
Worried about summer heat on a black dash? The parts for Chevrolet Traverse hold with 3M 468MP adhesive, and what makes the difference is preparation: degrease the plastic properly so no silicone dressing is left under the tape. A newer car or a big kit with lots of curves is a good job for a detailer or wrapper.
- Ships high-gloss; one thin coat of clear matt lacquer gives a matt look
- Wipe clean with a barely damp microfibre cloth
- No abrasives, just a quick wipe before the meet
Pick the finish for your next car meet and compare the parts diagram with your dash.
Preparing the surfaces before fitting
- Clean and degrease the original plastic: dust, silicone and trim dressings stop the 3M adhesive from gripping properly.
- Let everything dry completely and work under cover, in a mild garage, with good low-angle light.
- Lay the pieces out in the order of the diagram and have your own tools ready, as none are supplied with the kit.
FAQ
Is the kit available in matte?
The kit ships high-gloss. For a satin or matte look, spray one thin coat of clear matt aerosol lacquer for cars on the parts before fitting (for example SprayMax Klarlack matt or NOVOL Clearcoat Matt), let it dry, then fit as usual. One coat takes the gloss off; a second gives a flatter but slightly hazy look. Try a small part first. We don’t ship aerosols; you’ll find them in car accessory shops.
Do I need to remove the dashboard?
No. The pieces are stuck onto the existing panels.
Will it fit my Chevrolet Traverse?
Yes, if your dashboard matches the parts diagram and the version shown above. If in doubt, send us a photo.
Is the wood look real wood?
No – it is a printed decor under clear polyurethane.
Not sure which version you have? Send a photo of your dashboard and the reference via the contact form – we check it before we make your kit.
Buyer guide · Material guide · Installation guide
CockpitDekor · made to order since 1998
5483230005062
The kit is fitted over the existing surfaces – no dismantling of the dashboard.
- Clean and degrease every surface; silicone and interior sprays stop the adhesive from holding.
- Dry-fit each part against the parts diagram before removing the backing film.
- In a cold car, warm the parts and the dashboard slightly first.
- Press each part firmly from the centre to the edges.
- Avoid washing or stressing the edges for 24–72 hours.
Every kit is made in your choice of finish, protected by a high-gloss 3D polyurethane layer.
- Wood (burl, walnut, maple): warm, classic, premium look.
- Carbon fibre: sporty and technical.
- Brushed aluminium: cool, modern, close to OEM.
- Piano black and solid colours: clean or personalised.
- The finish changes the look only – always check the version of your dashboard first.
A kit is made for one exact dashboard layout. Before ordering, check:
- make, model, production year and generation (before or after facelift);
- manual or automatic gearbox;
- manual or automatic climate control, radio / NAVI unit;
- the parts diagram and number of parts in the product photos;
- steering wheel position: select it in the option above the finishes.
3 Reviews
Careful fitting in cold weather
In cold weather I would not rush the installation. I dry fitted the piece several times, checked the dashboard line again, then removed the rear backing film and pressed from the centre out. A small squeegee helped finish the corners cleanly. Tested on a Iveco Daily interior with Brushed Aluminium finish.
Livraison correcte et belle finition
La qualité est bonne et le rendu final est propre. Il faut vraiment dégraisser la surface avant la pose. La livraison était sans problème. Testé sur un intérieur de Ford Transit avec finition Mahogany.
Careful fitting in cold weather
In cold weather I would not rush the installation. I dry fitted the piece several times, checked the dashboard line again, then removed the rear backing film and pressed from the centre out. A small squeegee helped finish the corners cleanly. Tested on a Citroën Jumper interior with Brushed Aluminium finish.
Tap to zoom
